Check Thickness für eine Tailor Rolled Platine¶
Die folgende Abbildung zeigt den Check Thickness Dialog für eine Tailor Rolled Platine.
![%%============================================================================================%%
%% DEFINTIONS %%
\SetPicture{9.4cm}
\clip (0,0) rectangle (\pw,\ph);
\setlength{\isX}{0.10\pw}
\setlength{\isY}{0.101\pw}
%%============================================================================================%%
%% Table %%
\node[anchor=south, nosep] (N) at (0.50\pw,0.001\ph)
{
\begin{minipage}[b]{11cm}
\begin{center}
\begin{tabular}{|r|l|}
\hline
1&Zurück zum Hauptmenü.\\ \hline
2&Aktiver Unterdialog, Check Thickness.\\ \hline
3&Fringe Einstellungen.\\ \hline
\end{tabular}
\end{center}
\end{minipage}
};
%%============================================================================================%%
%% PICTURE 1 %%
\node[anchor=south, nosep] (A) at ($(N.north)+(0.00\pw,0.01\pw)$) {
\includegraphics[trim=0pt 0pt 0pt 973pt, clip=true, width=0.39\pw]{\PicturePath/Dialogs/DialogAssignTailorRolledBlankCheckThickness}
};
\node[anchor=south west, nosep] (B) at ($(A.north west)+(0.00\pw,0.00\pw)$) {
\includegraphics[trim=0pt 597pt 0pt 0pt, clip=true, width=0.39\pw]{\PicturePath/Dialogs/DialogAssignTailorRolledBlankCheckThickness}
};
\draw[picline] ($(B.north east)+(0.000\isX,-1.090\isY)$) to ($(B.north east)+(0.450\isX,-1.090\isY)$) node[piclabel]{1};
\draw[picline] ($(B.north east)+(0.000\isX,-1.490\isY)$) to ($(B.north east)+(0.450\isX,-1.490\isY)$) node[piclabel]{2};
\draw[picline] ($(B.north east)+(0.000\isX,-2.590\isY)$) to ($(B.north east)+(0.450\isX,-2.590\isY)$) node[piclabel]{3};
%%============================================================================================%%
%% TOOLS %%
%\PictureFrame](_images/tikz/tikz-DialogAssignTailorRolledBlankCheckThickness.png)
Check Thickness Dialog für Tailor Rolled Platinen
Der Check Thickness Dialog kennt nur den Abschnitt Fringe Scale zum Einstellen der Fringe-Darstellung. Mit Hilfe des Dropdown Menüs Scale können Sie die gewünschte Fringe-Darstellung auswählen, siehe folgende Abbildung.
![%%============================================================================================%%
%% DEFINTIONS %%
\SetPicture{1.7cm}
\clip (0,0) rectangle (\pw,\ph);
\setlength{\isX}{0.10\pw}
\setlength{\isY}{0.10\pw}
%%============================================================================================%%
%% PICTURE 1 %%
\node[anchor=south, nosep] (A) at (0.50\pw,0.0025\pw) {
\includegraphics[width=0.25\pw]{\PicturePath/Dialogs/DialogAssignTailorRolledBlankCheckThicknessDropDownMenuScale}
};
%%============================================================================================%%
%% TOOLS %%
%\PictureFrame](_images/tikz/tikz-DialogAssignTailorRolledBlankCheckThicknessDropDownMenuScale.png)
Check Thickness Dialog für Tailor Rolled Platinen, Dropdown Menü Scale
Es werden Darstellungen in den Standardfarben von OpenForm, Autoform und XIndeed angeboten. Den Minimal- und Maximalwert können Sie nach Setzen des Schalters “User Range” anpassen.
Die folgenden Abbildungen zeigen ein Beispiel für die drei Darstellungsarten.
![%%============================================================================================%%
%% DEFINTIONS %%
\SetPicture{10.9cm}
\clip (0,0) rectangle (\pw,\ph);
\setlength{\isX}{0.1\pw}
%%============================================================================================%%
%% PICTURE 1 %%
\node[anchor=south, nosep] (A) at (0.50\pw,0.00\pw) {
\includegraphics[width=1.00\pw]{\PicturePath/Dialogs/DialogAssignTailorRolledBlankCheckThicknessExample1}
};
%%============================================================================================%%
%% TOOLS %%
%\PictureFrame](_images/tikz/tikz-DialogAssignTailorRolledBlankCheckThicknessExample1.png)
Check Thickness Dialog für Tailor Rolled Platinen, OpenForm Fringes
![%%============================================================================================%%
%% DEFINTIONS %%
\SetPicture{10.9cm}
\clip (0,0) rectangle (\pw,\ph);
\setlength{\isX}{0.1\pw}
%%============================================================================================%%
%% PICTURE 1 %%
\node[anchor=south, nosep] (A) at (0.50\pw,0.00\pw) {
\includegraphics[width=1.00\pw]{\PicturePath/Dialogs/DialogAssignTailorRolledBlankCheckThicknessExample2}
};
%%============================================================================================%%
%% TOOLS %%
%\PictureFrame](_images/tikz/tikz-DialogAssignTailorRolledBlankCheckThicknessExample2.png)
Check Thickness Dialog für Tailor Rolled Platinen, Autoform Fringes
![%%============================================================================================%%
%% DEFINTIONS %%
\SetPicture{10.9cm}
\clip (0,0) rectangle (\pw,\ph);
\setlength{\isX}{0.1\pw}
%%============================================================================================%%
%% PICTURE 1 %%
\node[anchor=south, nosep] (A) at (0.50\pw,0.00\pw) {
\includegraphics[width=1.00\pw]{\PicturePath/Dialogs/DialogAssignTailorRolledBlankCheckThicknessExample3}
};
%%============================================================================================%%
%% TOOLS %%
%\PictureFrame](_images/tikz/tikz-DialogAssignTailorRolledBlankCheckThicknessExample3.png)
Check Thickness Dialog für Tailor Rolled Platinen, XIndeed Fringes